This is the serial console. Whatever you type or paste here will be send to COM1.

In Linux it can be accessed with `cat /dev/ttyS0`
(../../boot/freeldr/freeldr/arch/i386/hwpci.c:73) err: No valid routing table found!
(../../ntoskrnl/kd/kdio.c:376) -----------------------------------------------------
(../../ntoskrnl/kd/kdio.c:377) ReactOS 0.4-SVN (Build 20150220-r66365)
(../../ntoskrnl/kd/kdio.c:379) 1 System Processor [255 MB Memory]
(../../ntoskrnl/kd/kdio.c:380) Command Line: DEBUG DEBUGPORT=COM1 BAUDRATE=115200 SOS MININT
(../../ntoskrnl/kd/kdio.c:384) ARC Paths: multi(0)disk(0)cdrom(96) \ multi(0)disk(0)cdrom(96) \reactos\
(../../ntoskrnl/ke/i386/cpu.c:494) Supported CPU features : KF_V86_VIS KF_RDTSC KF_CR4 KF_CMOV KF_GLOBAL_PAGE KF_LARGE_PAGE  KF_CMPXCHG8B  KF_WORKING_PTE   KF_FAST_SYSCALL        
(../../ntoskrnl/ke/i386/cpu.c:801) Prefetch Cache: 64 bytes	L2 Cache: 262144 bytes	L2 Cache Line: 64 bytes	L2 Cache Associativity: 8
(../../ntoskrnl/mm/mminit.c:260)           0x80000000 - 0x83000000	Boot Loaded Image
(../../ntoskrnl/mm/mminit.c:264)           0xB0000000 - 0xB01C1000	PFN Database
(../../ntoskrnl/mm/mminit.c:268)           0xB01C1000 - 0xB0991000	ARM3 Non Paged Pool
(../../ntoskrnl/mm/mminit.c:272)           0xB9400000 - 0xBB400000	System View Space
(../../ntoskrnl/mm/mminit.c:276)           0xBB400000 - 0xC0000000	Session Space
(../../ntoskrnl/mm/mminit.c:279)           0xC0000000 - 0xC03FFFFF	Page Tables
(../../ntoskrnl/mm/mminit.c:282)           0xC0300000 - 0xC0300FFF	Page Directories
(../../ntoskrnl/mm/mminit.c:285)           0xC0400000 - 0xC07FFFFF	Hyperspace
(../../ntoskrnl/mm/mminit.c:289)           0xE1000000 - 0xED400000	ARM3 Paged Pool
(../../ntoskrnl/mm/mminit.c:292)           0xF4C00000 - 0xFA269000	System PTE Space
(../../ntoskrnl/mm/mminit.c:295)           0xFA269000 - 0xFFBE0000	Non Paged Pool Expansion PTE Space
(../../ntoskrnl/config/cmcheck.c:25) CmCheckRegistry(0xB073E008, 2) is UNIMPLEMENTED!
(../../hal/halx86/legacy/bussupp.c:623) Found parent bus (indicating PCI Bridge). PCI devices may fail!

====== PCI BUS HARDWARE DETECTION =======

00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma] [8086:1237] (rev 02)
	Subsystem: Unknown [0000:0000]
	Flags: fast devsel, latency 0
	Device has Extended Address Decoding. It may fail to work on older BIOSes!

00:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] [8086:7000] (rev 00)
	Subsystem: Unknown [0000:0000]
	Flags: bus master, medium devsel, latency 0

00:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8029(AS) [10ec:8029] (rev 00)
	Subsystem: QEMU Virtual Machine [1af4:1100]
	Flags: fast devsel, latency 0, IRQ 11
	I/O ports at b800 [size=2K]
	Device is using IRQ 11! ISA Cards using that IRQ may fail!

00:12.0 VGA compatible controller [0300]: NVIDIA Corporation GT216 [GeForce GT 220] [10de:0a20] (rev a2)
	Subsystem: GLoria L [0000:0000]
	Flags: bus master, fast devsel, latency 0, IRQ 10
	Memory at e0000000 (32-bit, prefetchable) [size=512M]
	Device is using IRQ 10! ISA Cards using that IRQ may fail!

00:1f.0 IDE interface [0101]: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 [8086:3a20] (rev 00)
	Subsystem: P5Q Deluxe Motherboard [1043:82d4]
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 14
	I/O ports at 01f0 [size=16]
	I/O ports at 03f4 [size=4]
	I/O ports at c000 [size=16K]

====== PCI BUS DETECTION COMPLETE =======

PC Compatible Eisa/Isa HAL Detected
(../../ntoskrnl/io/iomgr/driver.c:1630) '\Driver\SACDRV' initialization failed, status (0xc0000037)
(../../ntoskrnl/io/iomgr/driver.c:64) Deleting driver object '\Driver\SACDRV'


ATAPI IDE MiniPort Driver (UniATA) v 0.45e
 Parameter PrintLogo
 Parameter PrintLogo = 0x0
UniATA Init: OS should be ReactOS
UniATA Init: OS ver 4.1 (1), 1 CPU(s)
Performance calibration: dt=14995, counter=1933
InitBadBlocks general
InitBadBlocks returned: 0xc0000034
UniataInitAtaCommands:
 Parameter SkipRaids
 Parameter SkipRaids = 0x1
 Parameter ForceSimplex
 Parameter ForceSimplex = 0x0
 Parameter LogToDisplay
 Parameter LogToDisplay = 0x0
HwInitializationDataSize = 50
set NeedPhysicalAddresses = TRUE
set AtapiAdapterControl() ptr


ATAPI IDE enum supported BusMaster Devices
 Parameter VirtualMachineType
 Parameter VirtualMachineType = 0x0
 Parameter VirtualBox
 Parameter VirtualBox = 0x0
-- BusID: 0x0:0x5:0x0 - QEmu
-- BusID: 0x0:0x1f:0x0
Storage Class
DevId = 3A208086 Class = 0001/0001, ProgIf 8F
(!) InterruptPin = 0x1
(!) InterruptLine = 0xe
 Parameter Include
 Parameter Include = 0x0
No force include, check exclude
 Parameter Exclude
 Parameter Exclude = 0x0
Default device
found, pass 0
InterruptPin = 0x1
InterruptLine = 0xe
Enabling Mem/Io spaces and busmastering...
Initial pciData.Command = 0x5
PCI_ENABLE_IO_SPACE
PCI_ENABLE_MEMORY_SPACE
New pciData.Command = 0x5
PCI_ENABLE_BUS_MASTER
InterruptLine = 0xe
Final pciData.Command = 0x5
Range 0 = 0x1f1
Range 1 = 0x3f5
Range 4 = 0xc001
count: BMListLen++
-- BusID: 0x0:0x5:0x0 - QEmu
-- BusID: 0x0:0x1f:0x0
Storage Class
DevId = 3A208086 Class = 0001/0001, ProgIf 8F
(!) InterruptPin = 0x1
(!) InterruptLine = 0xe
 Parameter Include
 Parameter Include = 0x0
No force include, check exclude
 Parameter Exclude
 Parameter Exclude = 0x0
Default device
found, pass 1
InterruptPin = 0x1
InterruptLine = 0xe
Range 0 = 0x1f1
Range 1 = 0x3f5
Range 4 = 0xc001
found suitable device
-- BusID: 0x0:0x5:0x0 - QEmu
-- BusID: 0x0:0x1f:0x0
Storage Class
DevId = 3A208086 Class = 0001/0001, ProgIf 8F
(!) InterruptPin = 0x1
(!) InterruptLine = 0xe
 Parameter Include
 Parameter Include = 0x0
No force include, check exclude
 Parameter Exclude
 Parameter Exclude = 0x0
Default device
found, pass 2
InterruptPin = 0x1
InterruptLine = 0xe
Range 0 = 0x1f1
Range 1 = 0x3f5
Range 4 = 0xc001
found suitable device
Add to BMList, AltInit 0
  BMListLen=1
 Parameter WaitBusyCount
 Parameter WaitBusyCount = 0xc8
 Parameter WaitBusyDelay
 Parameter WaitBusyDelay = 0xa
 Parameter WaitDrqDelay
 Parameter WaitDrqDelay = 0xa
 Parameter WaitBusyLongCount
 Parameter WaitBusyLongCount = 0x7d0
 Parameter WaitBusyLongDelay
 Parameter WaitBusyLongDelay = 0xfa
 Parameter AtapiSendDisableIntr
 Parameter AtapiSendDisableIntr = 0x0
 Parameter AtapiDmaRawRead
 Parameter AtapiDmaRawRead = 0x1
 Parameter MaxIsrWait
 Parameter MaxIsrWait = 0x28


ATAPI IDE: Look for legacy ISA-bridged PCI IDE controller (onboard)


ATAPI IDE: BMListLen 1
!BMList[i].MasterDev


ATAPI IDE: Look for PCI IDE controller


ATAPI IDE: i 0, BMListLen 1
 Parameter IgnoreNativePci
 Parameter IgnoreNativePci = 0x0
Try init 8086 3a20 
(../../hal/halx86/legacy/bussupp.c:1159) Slot assignment for 5 on bus 0
(../../hal/halx86/legacy/bus/pcibus.c:719) WARNING: PCI Slot Resource Assignment is FOOBAR
UniataFindBusMasterController: Context=0, BMListLen=1
ConfigInfo->Length 8c
bm_offset 0, channel 0 
AdapterInterfaceType=0x5
IoBusNumber=0x0
slotNumber=0x1f
busDataRead
DevId = 3A208086 Class = 0001/0001
Storage Class
UniataChipDetect:
HwFlags: 0x0
 Parameter ForceSimplex
 Parameter ForceSimplex = 0x0
i: 0x33
VendorID/DeviceID/Rev 0x8086/0x3a20/0x0
i: 0x37
HwFlags: 0x10000400
 Parameter HwFlagsOverride
 Parameter HwFlagsOverride = 0x10000400
HwFlagsOverride: 0x10000400
 Parameter HwFlagsAdd
 Parameter HwFlagsAdd = 0x0
HwFlagsAdd: 0x0
HwFlags (final): 0x10000400
MaxTransferMode: 0x48
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
MaxTransferMode (overriden): 0x48
UniataChipDetectChannels:
 Parameter IgnoreAhciPM
 Parameter IgnoreAhciPM = 0x1
SATA/AHCI w/o PM, max luns 1 or 2
 Parameter Exclude
 Parameter Exclude = 0x0
 Parameter Exclude
 Parameter Exclude = 0x0
PortMask 0x3
 Parameter PortMask
 Parameter PortMask = 0x3
Force PortMask 0x3
mask -> 2 chans
 Parameter NumberChannels
 Parameter NumberChannels = 0x2
reg -> 2 chans
Final PortMask 0x3
allocate 2 Luns for 2 channels
Intel chip config: 0
  AtapiGetIoRange:
  AtapiGetIoRange: rid 0x5, start 0x0, offs 0x0, len 0x10, mem 0x0
  AtapiGetIoRange: (2) 0x0
other Intel
other Intel
ForceSimplex = 0
HwFlags = 10000400
 (0)HwFlags = 10000400
 (1)HwFlags = 10000400
 (2)found suitable device
HwFlags = 10000400
 (3)Range 0 = 0x1f1
Range 1 = 0x3f5
Range 4 = 0xc001
IsBusMaster == TRUE
  AtapiGetIoRange:
  AtapiGetIoRange: rid 0x4, start 0x0, offs 0x0, len 0x10, mem 0x0
  AtapiGetIoRange: (2) 0xc000
  BusMasterAddress (base): 0xc000
IsBusMaster == TRUE && !MasterDev
  BM statusByte = 0
AtapiReadChipConfig: devExt 0xb073a4bc
AtapiReadChipConfig: dev 0x0, ph chan -1
 Parameter ForceSimplex
 Parameter ForceSimplex = 0x0
MaxTransferMode (base): 0x48
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
MaxTransferMode (overriden): 0x48
 Parameter Force80pin
 Parameter Force80pin = 0x0
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
MaxTransferMode (overriden): 0x48
 Parameter Force80pin
 Parameter Force80pin = 0x0
 Parameter AtapiDmaZeroTransfer
 Parameter AtapiDmaZeroTransfer = 0x0
 Parameter AtapiDmaControlCmd
 Parameter AtapiDmaControlCmd = 0x0
 Parameter AtapiDmaRawRead
 Parameter AtapiDmaRawRead = 0x1
 Parameter AtapiDmaReadWrite
 Parameter AtapiDmaReadWrite = 0x1
AtapiChipInit: dev 0x0, ph chan -2, c -1
HwFlags: 0x10000400
VendorID/DeviceID/Rev 0x8086/0x3a20/0x0
Intel SATA
Base init
simplexOnly = 0 (2)!MasterDev
update ConfigInfo->nt4
using AtaReq sz 1000
update ConfigInfo->w2k: 64bit 0
chan[0] InterruptMode: 0, Level 14, Level2 0, Vector 14, Vector2 0
Reconstruct ConfigInfo
set Dma32BitAddresses
BMList[i].channel 0x0, NumberChannels 0x2, channel 0x0
de 0xb073a4bc, Channel 0x0
chan = 0xb0739008
AtapiSetupLunPtrs for channel 0 of 2, 2 luns 
  Chan 0xb0739008
  Lun 0x0
  Lun ptr 0xb0963000
  Lun 0x1
  Lun ptr 0xb0963308
AtapiReadChipConfig: devExt 0xb073a4bc
AtapiReadChipConfig: dev 0x0, ph chan 0
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
MaxTransferMode (overriden): 0x48
 Parameter ReorderEnable
 Parameter ReorderEnable = 0x1
 Parameter Force80pin
 Parameter Force80pin = 0x0
 Parameter ReadCacheEnable
 Parameter ReadCacheEnable = 0x1
 Parameter WriteCacheEnable
 Parameter WriteCacheEnable = 0x1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
 Parameter PreferedTransferMode
 Parameter PreferedTransferMode = 0xffffffff
 Parameter AdvancedPowerMode
 Parameter AdvancedPowerMode = 0x80
 Parameter AcousticMgmt
 Parameter AcousticMgmt = 0x80
 Parameter StandbyTimer
 Parameter StandbyTimer = 0x0
 Parameter ReadOnly
 Parameter ReadOnly = 0x0
 Parameter GeomType
 Parameter GeomType = 0xffffffff
 Parameter Hidden
 Parameter Hidden = 0x0
 Parameter ReadCacheEnable
 Parameter ReadCacheEnable = 0x1
 Parameter WriteCacheEnable
 Parameter WriteCacheEnable = 0x1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
 Parameter PreferedTransferMode
 Parameter PreferedTransferMode = 0xffffffff
 Parameter AdvancedPowerMode
 Parameter AdvancedPowerMode = 0x80
 Parameter AcousticMgmt
 Parameter AcousticMgmt = 0x80
 Parameter StandbyTimer
 Parameter StandbyTimer = 0x0
 Parameter ReadOnly
 Parameter ReadOnly = 0x0
 Parameter GeomType
 Parameter GeomType = 0xffffffff
 Parameter Hidden
 Parameter Hidden = 0x0
Getting IO ranges
!MasterDev mode
IO range 1 0x1f0
IO range 2 0x3f6
IDX_IO1 0->1f0(io)
IDX_IO2 10->3f6(io)
IDX_BM_IO 14->c000(io)
IDX_SATA_IO 19->0(io)
  AltStatus (0x50)
  Reg_0x1 (0x1f1) = 0x0
  Reg_0x2 (0x1f2) = 0x2
  Reg_0x3 (0x1f3) = 0x0
  Reg_0x4 (0x1f4) = 0x0
  Reg_0x5 (0x1f5) = 0x0
  Reg_0x6 (0x1f6) = 0xa0
  Reg_0x7 (0x1f7) = 0x50
  BM_0x0 (0xc000) = 0x1
  BM_0x1 (0xc001) = 0xff
  BM_0x2 (0xc002) = 0x0
  BM_0x3 (0xc003) = 0xff
clean IDE intr 0
clean IDE intr 1
  DMA status 0x0
AtapiDmaAlloc: allocate tmp buffers below 4Gb
AtapiVirtToPhysAddr_: b0962008 -> 00000000:037a1008
AtapiVirtToPhysAddr_: b0719000 -> 00000000:03558000
de 0xb073a4bc, Channel 0x1
chan = 0xb0739270
AtapiSetupLunPtrs for channel 1 of 2, 2 luns 
  Chan 0xb0739270
  Lun 0x0
  Lun ptr 0xb0963610
  Lun 0x1
  Lun ptr 0xb0963918
AtapiReadChipConfig: devExt 0xb073a4bc
AtapiReadChipConfig: dev 0x0, ph chan 1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
MaxTransferMode (overriden): 0x48
 Parameter ReorderEnable
 Parameter ReorderEnable = 0x1
 Parameter Force80pin
 Parameter Force80pin = 0x0
 Parameter ReadCacheEnable
 Parameter ReadCacheEnable = 0x1
 Parameter WriteCacheEnable
 Parameter WriteCacheEnable = 0x1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
 Parameter PreferedTransferMode
 Parameter PreferedTransferMode = 0xffffffff
 Parameter AdvancedPowerMode
 Parameter AdvancedPowerMode = 0x80
 Parameter AcousticMgmt
 Parameter AcousticMgmt = 0x80
 Parameter StandbyTimer
 Parameter StandbyTimer = 0x0
 Parameter ReadOnly
 Parameter ReadOnly = 0x0
 Parameter GeomType
 Parameter GeomType = 0xffffffff
 Parameter Hidden
 Parameter Hidden = 0x0
 Parameter ReadCacheEnable
 Parameter ReadCacheEnable = 0x1
 Parameter WriteCacheEnable
 Parameter WriteCacheEnable = 0x1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0x48
 Parameter PreferedTransferMode
 Parameter PreferedTransferMode = 0xffffffff
 Parameter AdvancedPowerMode
 Parameter AdvancedPowerMode = 0x80
 Parameter AcousticMgmt
 Parameter AcousticMgmt = 0x80
 Parameter StandbyTimer
 Parameter StandbyTimer = 0x0
 Parameter ReadOnly
 Parameter ReadOnly = 0x0
 Parameter GeomType
 Parameter GeomType = 0xffffffff
 Parameter Hidden
 Parameter Hidden = 0x0
ScsiPortValidateRange failed (1)
exit: init spinlock
MasterDev=0x0, NumberChannels=0x2, Isr2DevObj=0x0
Init ISR:
Multichannel native mode, go...
Create DO
DO name:  len(38, 38), \Device\uniata0_2ch
HalGetInterruptVector
  OrigAdapterInterfaceType=5
  SystemIoBusNumber=0
  BusInterruptLevel=14
  BusInterruptVector=14
isr2_de 0xb0739e18
isr2_vector 0x3e
isr2_irql 0xd
isr2_affinity 0x1
IoConnectInterrupt
MasterDev=0x0, NumberChannels=0x2, Isr2DevObj=0xb0739d60
final chan[2] InterruptMode: 0, Level 14, Level2 0, Vector 14, Vector2 0
return SP_RETURN_FOUND
AtapiHwInitialize: (base)
AtapiChipInit: dev 0xffffffff, ph chan -1, c -1
HwFlags: 0x10000400
VendorID/DeviceID/Rev 0x8086/0x3a20/0x0
Intel SATA
Base init
AtapiChipInit: dev 0xffffffff, ph chan 0, c 0
HwFlags: 0x10000400
VendorID/DeviceID/Rev 0x8086/0x3a20/0x0
Intel SATA
channel init
reg 90: 0, init lun map
chan 0
other Intel
0 -> 0/2
FindDevices:
AtapiDisableInterrupts_0: 0
  max_ldev 2
CheckDevice: Device 0x0
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
  HDD at home
  HDD at home
CheckDevice: status 0x50
CheckDevice: IDE device check
IssueIdentify: Checking for IDE. Status (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
IssueIdentify: Status before read words 0x50
IssueIdentify: statusByte 0x50
IssueIdentify: !IDE_STATUS_DRQ (2) (0x50)
CheckDevice: check status: not found
CheckDevice: Device 0x1
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
  HDD at home
  HDD at home
CheckDevice: status 0x50
CheckDevice: IDE device check
IssueIdentify: Checking for IDE. Status (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
IssueIdentify: Status before read words 0x50
IssueIdentify: statusByte 0x50
IssueIdentify: !IDE_STATUS_DRQ (2) (0x50)
CheckDevice: check status: not found
AtapiEnableInterrupts_0: 1
FindDevices: returning 0
AtapiHwInitialize: lChannel 0x0, dev 0
AtapiHwInitialize: lChannel 0x0, dev 1
AtapiChipInit: dev 0xffffffff, ph chan 1, c 1
HwFlags: 0x10000400
VendorID/DeviceID/Rev 0x8086/0x3a20/0x0
Intel SATA
channel init
reg 90: 0, init lun map
chan 1
other Intel
0 -> 1/3
FindDevices:
AtapiDisableInterrupts_1: 0
  max_ldev 2
CheckDevice: Device 0x0
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 ff:
  DMA status 0xff
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
  nobody home! 0xff != 0x55
CheckDevice: Device 0x1
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 ff:
  DMA status 0xff
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
  nobody home! 0xff != 0x55
AtapiEnableInterrupts_1: 1
FindDevices: returning 0
AtapiHwInitialize: lChannel 0x1, dev 0
AtapiHwInitialize: lChannel 0x1, dev 1
AtapiHwInitialize: (base) done
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x0:0x0:0x0
   VendorID+DeviceID/Rev 0x3a208086/0x0
UniataNeedQueueing: TopLevel, qd=0
Send to device 12
TopLevel (2), srb 0xf9eccf90
TopLevel (3), AtaReq 0xb0951000
  HDD at home
CheckDevice: Device 0x0
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
  HDD at home
  HDD at home
CheckDevice: status 0x50
CheckDevice: IDE device check
IssueIdentify: Checking for IDE. Status (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 0
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
IssueIdentify: Status before read words 0x50
IssueIdentify: statusByte 0x50
IssueIdentify: !IDE_STATUS_DRQ (2) (0x50)
CheckDevice: check status: not found
AtapiStartIo: SRB rejected
SRB_STATUS_SELECTION_TIMEOUT
AtapiStartIo: Srb 0xf9eccf90 complete with status 0xa
AtapiStartIo: AtapiDmaDBSync(b0739008, f9eccf90)
AtapiStartIo: UniataRemoveRequest(b0739008, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan b0739008, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
AtapiInterrupt2: NOT ACTIVE cntrlr 0x0 chan 0x0
Intr: VendorID+DeviceID/Rev 0x3a208086/0x0 (ex 0)
unexpected, 1st chance
AtapiInterrupt(base): cntrlr 0x0 chan 0x0
AtapiInterrupt(base): try lock
AtapiInterrupt(base): locked
AtapiCheckInterrupt__:
  cntrlr 0x0:0x0, lch 0x0 DmaTransfer = FALSE
  DMA status 0x0
  perform generic check
  getting status...
  IDE status 0x50
  base status 0x50
  Unexpected interrupt.
  OurInterrupt = 0
AtapiInterrupt(base): set CHECK_INTR_IDLE (2)
AtapiInterrupt(base): cntrlr 0x0 chan 0x1
AtapiInterrupt(base): try lock
AtapiInterrupt(base): locked
AtapiCheckInterrupt__:
  cntrlr 0x0:0x1, lch 0x1 DmaTransfer = FALSE
  DMA status 0xff
  perform generic check
  clear unexpected DMA intr
AtapiDmaDone: dev -1
  getting status...
  IDE status 0xff
  base status 0xff
  Unexpected interrupt.
  OurInterrupt = 2
AtapiInterrupt(base): Catch unexpected
AtapiInterrupt(base): exit with status 0x1
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x0:0x0:0x1
   VendorID+DeviceID/Rev 0x3a208086/0x0
UniataNeedQueueing: TopLevel, qd=0
Send to device 12
TopLevel (2), srb 0xf9eccf90
TopLevel (3), AtaReq 0xb0951000
  HDD at home
CheckDevice: Device 0x1
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
  HDD at home
  HDD at home
CheckDevice: status 0x50
CheckDevice: IDE device check
IssueIdentify: Checking for IDE. Status (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x4
  clear unexpected DMA intr on ATAPI reset
AtapiDmaDone: dev 1
AtapiDisableInterrupts_0: 0
AtapiEnableInterrupts_0: 1
IssueIdentify: Status after soft reset (0x50)
IssueIdentify: Status before read words 0x50
IssueIdentify: statusByte 0x50
IssueIdentify: !IDE_STATUS_DRQ (2) (0x50)
CheckDevice: check status: not found
AtapiStartIo: SRB rejected
SRB_STATUS_SELECTION_TIMEOUT
AtapiStartIo: Srb 0xf9eccf90 complete with status 0xa
AtapiStartIo: AtapiDmaDBSync(b0739008, f9eccf90)
AtapiStartIo: UniataRemoveRequest(b0739008, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan b0739008, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
AtapiInterrupt2: NOT ACTIVE cntrlr 0x0 chan 0x0
Intr: VendorID+DeviceID/Rev 0x3a208086/0x0 (ex 0)
unexpected, 1st chance
AtapiInterrupt(base): cntrlr 0x0 chan 0x1
AtapiInterrupt(base): try lock
AtapiInterrupt(base): locked
AtapiCheckInterrupt__:
  cntrlr 0x0:0x1, lch 0x1 DmaTransfer = FALSE
  DMA status 0xff
  perform generic check
  clear unexpected DMA intr
AtapiDmaDone: dev -1
  getting status...
  IDE status 0xff
  base status 0xff
  Unexpected interrupt.
  OurInterrupt = 2
AtapiInterrupt(base): Catch unexpected
AtapiInterrupt(base): cntrlr 0x0 chan 0x0
AtapiInterrupt(base): try lock
AtapiInterrupt(base): locked
AtapiCheckInterrupt__:
  cntrlr 0x0:0x0, lch 0x0 DmaTransfer = FALSE
  DMA status 0x0
  perform generic check
  getting status...
  IDE status 0x50
  base status 0x50
  Unexpected interrupt.
  OurInterrupt = 0
AtapiInterrupt(base): set CHECK_INTR_IDLE (2)
AtapiInterrupt(base): exit with status 0x1
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x1:0x0:0x0
   VendorID+DeviceID/Rev 0x3a208086/0x0
UniataNeedQueueing: TopLevel, qd=0
Send to device 12
TopLevel (2), srb 0xf9eccf90
TopLevel (3), AtaReq 0xb0951000
  nobody home! 0xff != 0x55
AtapiStartIo: SRB rejected
SRB_STATUS_SELECTION_TIMEOUT
AtapiStartIo: Srb 0xf9eccf90 complete with status 0xa
AtapiStartIo: AtapiDmaDBSync(b0739270, f9eccf90)
AtapiStartIo: UniataRemoveRequest(b0739270, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan b0739270, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x1:0x0:0x1
   VendorID+DeviceID/Rev 0x3a208086/0x0
UniataNeedQueueing: TopLevel, qd=0
Send to device 12
TopLevel (2), srb 0xf9eccf90
TopLevel (3), AtaReq 0xb0951000
  nobody home! 0xff != 0x55
AtapiStartIo: SRB rejected
SRB_STATUS_SELECTION_TIMEOUT
AtapiStartIo: Srb 0xf9eccf90 complete with status 0xa
AtapiStartIo: AtapiDmaDBSync(b0739270, f9eccf90)
AtapiStartIo: UniataRemoveRequest(b0739270, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan b0739270, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x2:0x0:0x0
   VendorID+DeviceID/Rev 0x3a208086/0x0
AtapiStartIo: Communication port
  INQUIRY
AtapiStartIo: Srb 0xf9eccf90 complete with status 0x1
AtapiStartIo: UniataRemoveRequest(0, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan 0, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x2:0x1:0x0
   VendorID+DeviceID/Rev 0x3a208086/0x0
AtapiStartIo: SRB rejected
SRB_STATUS_SELECTION_TIMEOUT
AtapiStartIo: Srb 0xf9eccf90 complete with status 0xa
AtapiStartIo: UniataRemoveRequest(0, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan 0, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
TopLevel
** AtapiStartIo: Function 0x0, PATH:LUN:TID = 0x2:0x0:0x1
   VendorID+DeviceID/Rev 0x3a208086/0x0
AtapiStartIo: SRB rejected
SRB_STATUS_SELECTION_TIMEOUT
AtapiStartIo: Srb 0xf9eccf90 complete with status 0xa
AtapiStartIo: UniataRemoveRequest(0, f9eccf90)
AtapiStartIo: ScsiPortNotification
AtapiStartIo: UniataGetCurRequest
AtapiStartIo: chan 0, Src 0
AtapiStartIo: next Srb 0
AtapiStartIo: query PORT for next request
ScsiPortInitialize Status 0x0
 Parameter IgnoreIsa
 Parameter IgnoreIsa = 0x0


ATAPI IDE: Look for ISA Controllers
AtapiFindController:
  assume max PIO4
allocate 2 Luns for 1 channels
AtapiSetupLunPtrs for channel 0 of 1, 2 luns 
  Chan 0xb0950b30
  Lun 0x0
  Lun ptr 0xb0716008
  Lun 0x1
  Lun ptr 0xb0716310
AtapiReadChipConfig: devExt 0xb09502b4
AtapiReadChipConfig: dev 0xffffffff, ph chan -1
 Parameter ForceSimplex
 Parameter ForceSimplex = 0x0
MaxTransferMode (base): 0xc
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0xc
MaxTransferMode (overriden): 0xc
 Parameter Force80pin
 Parameter Force80pin = 0x0
 Parameter AtapiDmaZeroTransfer
 Parameter AtapiDmaZeroTransfer = 0x0
 Parameter AtapiDmaControlCmd
 Parameter AtapiDmaControlCmd = 0x0
 Parameter AtapiDmaRawRead
 Parameter AtapiDmaRawRead = 0x1
 Parameter AtapiDmaReadWrite
 Parameter AtapiDmaReadWrite = 0x1
AtapiChipInit: dev 0xffffffff, ph chan -1, c -1
HwFlags: 0x0
VendorID/DeviceID/Rev 0x0/0x0/0x0
 Parameter PortBase
 Parameter PortBase = 0x0
 Parameter Irq
 Parameter Irq = 0x0
  BaseIoAddress1=1f0
  BaseIoAddress2=3f6
  AltStatus (0x50)
  Reg_0x1 (0x1f1) = 0x0
  Reg_0x2 (0x1f2) = 0x0
  Reg_0x3 (0x1f3) = 0x0
  Reg_0x4 (0x1f4) = 0x0
  Reg_0x5 (0x1f5) = 0x0
  Reg_0x6 (0x1f6) = 0xa0
  Reg_0x7 (0x1f7) = 0x50
  BM_0x0 (0x0) = 0xff
  BM_0x1 (0x0) = 0xff
  BM_0x2 (0x0) = 0xff
  BM_0x3 (0x0) = 0xff
de 0xb09502b4, Channel ???
chan = 0xb0950b30
AtapiReadChipConfig: devExt 0xb09502b4
AtapiReadChipConfig: dev 0xffffffff, ph chan 0
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0xc
MaxTransferMode (overriden): 0xc
 Parameter ReorderEnable
 Parameter ReorderEnable = 0x1
 Parameter Force80pin
 Parameter Force80pin = 0x0
 Parameter ReadCacheEnable
 Parameter ReadCacheEnable = 0x1
 Parameter WriteCacheEnable
 Parameter WriteCacheEnable = 0x1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0xc
 Parameter PreferedTransferMode
 Parameter PreferedTransferMode = 0xffffffff
 Parameter AdvancedPowerMode
 Parameter AdvancedPowerMode = 0x80
 Parameter AcousticMgmt
 Parameter AcousticMgmt = 0x80
 Parameter StandbyTimer
 Parameter StandbyTimer = 0x0
 Parameter ReadOnly
 Parameter ReadOnly = 0x0
 Parameter GeomType
 Parameter GeomType = 0xffffffff
 Parameter Hidden
 Parameter Hidden = 0x0
 Parameter ReadCacheEnable
 Parameter ReadCacheEnable = 0x1
 Parameter WriteCacheEnable
 Parameter WriteCacheEnable = 0x1
 Parameter MaxTransferMode
 Parameter MaxTransferMode = 0xc
 Parameter PreferedTransferMode
 Parameter PreferedTransferMode = 0xffffffff
 Parameter AdvancedPowerMode
 Parameter AdvancedPowerMode = 0x80
 Parameter AcousticMgmt
 Parameter AcousticMgmt = 0x80
 Parameter StandbyTimer
 Parameter StandbyTimer = 0x0
 Parameter ReadOnly
 Parameter ReadOnly = 0x0
 Parameter GeomType
 Parameter GeomType = 0xffffffff
 Parameter Hidden
 Parameter Hidden = 0x0
AtapiChipInit: dev 0xffffffff, ph chan 0, c 0
HwFlags: 0x0
VendorID/DeviceID/Rev 0x0/0x0/0x0
UNIATA_NO80CHK
AtapiFindController: Found IDE at 0x1f0
AtapiFindController: Atapi Only (2)
AtapiFindController: look for devices
FindDevices:
AtapiDisableInterrupts_0: 0
  max_ldev 2
CheckDevice: Device 0x0
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
  HDD at home
  HDD at home
CheckDevice: status 0x50
CheckDevice: IDE device check
IssueIdentify: Checking for IDE. Status (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x0, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
IssueIdentify: Status before read words 0x50
IssueIdentify: statusByte 0x50
IssueIdentify: !IDE_STATUS_DRQ (2) (0x50)
CheckDevice: check status: not found
CheckDevice: Device 0x1
CheckDevice: reset dev
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
  HDD at home
  HDD at home
CheckDevice: status 0x50
CheckDevice: IDE device check
IssueIdentify: Checking for IDE. Status (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x20000 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
AtaCommand48: cntrlr 0x0:0x0 dev 0x1, cmd 0xec, lba 0x0 count 0x0 feature 0x0
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
  retry waiting DRQ, status 0x50
IssueIdentify: !IDE_STATUS_DRQ (0x50)
IssueIdentify: DRQ never asserted (0x50). Error reg (0x0)
AtapiSoftReset:
  statusByte2 50:
  DMA status 0x0
AtapiDisableInterrupts_0: 1
AtapiEnableInterrupts_0: 2
IssueIdentify: Status after soft reset (0x50)
IssueIdentify: Status before read words 0x50
IssueIdentify: statusByte 0x50
IssueIdentify: !IDE_STATUS_DRQ (2) (0x50)
CheckDevice: check status: not found
AtapiEnableInterrupts_0: 1
FindDevices: returning 0
 Parameter PortBase
 Parameter PortBase = 0x0
 Parameter Irq
 Parameter Irq = 0x0
  BaseIoAddress1=170
  BaseIoAddress2=376
  AltStatus (0xff)
  Reg_0x1 (0x171) = 0xff
  Reg_0x2 (0x172) = 0xff
  Reg_0x3 (0x173) = 0xff
  Reg_0x4 (0x174) = 0xff
  Reg_0x5 (0x175) = 0xff
  Reg_0x6 (0x176) = 0xff
  Reg_0x7 (0x177) = 0xff
  BM_0x0 (0x0) = 0xff
  BM_0x1 (0x0) = 0xff
  BM_0x2 (0x0) = 0xff
  BM_0x3 (0x0) = 0xff
AtapiFindController: Identifier read back from Master (0xff)
AtapiFindController: Identifier read back from Slave (0xff)
 Parameter PortBase
 Parameter PortBase = 0x0
 Parameter Irq
 Parameter Irq = 0x0
  BaseIoAddress1=1e8
  BaseIoAddress2=3ee
  AltStatus (0xff)
  Reg_0x1 (0x1e9) = 0xff
  Reg_0x2 (0x1ea) = 0xff
  Reg_0x3 (0x1eb) = 0xff
  Reg_0x4 (0x1ec) = 0xff
  Reg_0x5 (0x1ed) = 0xff
  Reg_0x6 (0x1ee) = 0xff
  Reg_0x7 (0x1ef) = 0xff
  BM_0x0 (0x0) = 0xff
  BM_0x1 (0x0) = 0xff
  BM_0x2 (0x0) = 0xff
  BM_0x3 (0x0) = 0xff
AtapiFindController: Identifier read back from Master (0xff)
AtapiFindController: Identifier read back from Slave (0xff)
 Parameter PortBase
 Parameter PortBase = 0x0
 Parameter Irq
 Parameter Irq = 0x0
  BaseIoAddress1=168
  BaseIoAddress2=36e
  AltStatus (0xff)
  Reg_0x1 (0x169) = 0xff
  Reg_0x2 (0x16a) = 0xff
  Reg_0x3 (0x16b) = 0xff
  Reg_0x4 (0x16c) = 0xff
  Reg_0x5 (0x16d) = 0xff
  Reg_0x6 (0x16e) = 0xff
  Reg_0x7 (0x16f) = 0xff
  BM_0x0 (0x0) = 0xff
  BM_0x1 (0x0) = 0xff
  BM_0x2 (0x0) = 0xff
  BM_0x3 (0x0) = 0xff
AtapiFindController: Identifier read back from Master (0xff)
AtapiFindController: Identifier read back from Slave (0xff)
AtapiFindController: return SP_RETURN_NOT_FOUND
ScsiPortInitialize Status 0xc00000c0
 Parameter IgnoreMca
 Parameter IgnoreMca = 0x0


ATAPI IDE: Look for MCA Controllers
ScsiPortInitialize Status 0xc00000c0


Leave UNIATA MiniPort DriverEntry with status 0x0
(../../ntoskrnl/io/iomgr/driver.c:1630) '\Driver\BUSLOGIC' initialization failed, status (0xc00000c0)
(../../ntoskrnl/io/iomgr/driver.c:64) Deleting driver object '\Driver\BUSLOGIC'
(../../ntoskrnl/io/iomgr/driver.c:64) Deleting driver object '\Driver\CDFS'
(../../ntoskrnl/mm/ARM3/sysldr.c:954) Leaking driver: cdfs.sys
(../../hal/halx86/legacy/halpnpdd.c:793) Illegal IRP: c
(../../hal/halx86/legacy/halpnpdd.c:793) Illegal IRP: c
(../../hal/halx86/legacy/halpnpdd.c:793) Illegal IRP: 15
(../../ntoskrnl/io/pnpmgr/pnpinit.c:321) IopOpenRegistryKeyEx() failed with Status C0000034
(../../ntoskrnl/io/iomgr/driver.c:735) ZwOpenKey() failed with Status C0000034
(../../ntoskrnl/io/iomgr/driver.c:735) ZwOpenKey() failed with Status C0000034
(../../hal/halx86/legacy/halpnpdd.c:793) Illegal IRP: d
(../../hal/halx86/legacy/halpnpdd.c:793) Illegal IRP: 14
(../../ntoskrnl/io/pnpmgr/pnpmgr.c:4059) IRP_MN_QUERY_PNP_DEVICE_STATE failed with status 0xc00000bb
(../../ntoskrnl/mm/ARM3/sysldr.c:3024) ZwOpenFile failed for '\SystemRoot\system32\drivers\vbemp.sys' with status 0xc000003a
(../../ntoskrnl/mm/ARM3/sysldr.c:3024) ZwOpenFile failed for '\SystemRoot\system32\drivers\vbemp.sys' with status 0xc000003a
(../../ntoskrnl/io/iomgr/iomgr.c:556) IopCreateArcNames failed: c0000034

*** Fatal System Error: 0x00000069
                       (0x00000000,0x00000000,0x00000000,0x00000000)


Entered debugger on embedded INT3 at 0x0008:0x8095ef58.
kdb:>